- Home /
- F2H-UE14FE Unframed E1-4FE interface Converter
This protocol converter (interface converter) using large scale FPGA design, ITU-T G.703 standard unframed E1 interfaces and four 10 / 100Base-T Ethernet interface converter, 10/100Base-T channels will be transferred to the switch, HUB, routers, bridges, or other device. And through Optical and other transport equipment were transferred, networking can be composed of different network segments. This device is a high performance, adaptive remote Ethernet bridge. Its small size, low cost, very suitable for cost-sensitive bridging applications or as a LAN extender or slicer bitstream on infrastructure. Can automatically learn continuously connected LAN MAC address on the destination address of the frame and another LAN forwarding. On the TCP / IP protocol transparent, provide security for the communication network between the different interface devices, seamless connectivity. This equipment is widely used between WAN and LAN networking, monitoring field.
Features
- - Based on self -copyright IC
- - Can realize monitor and control of remote equipment, OAM management data did not take up users’ timeslot and save E1 bandwidth
- - Have the function of E1 interface loop back check, avoid the converter crashed because of interface loop return;
- - Have indicator when the device is power-off or E1 line is broken or lose signal;
- - Can set the E1 line that not to send the LINK signal to Ethernet interface while E1 line is broken; The Ethernet interface supports jumbo frames (1916 Bytes);
- - 4Channel 10M/100M Ethernet interface can isolate each other to realize communication independently;
- - Ethernet interface supports10M/100M, half/full duplex auto-Negotiation and AUTO-MDIX (crossed line and straightly connected line self-adaptable );
- - Provide 2 clock types: E1 master clock and E1 line clock;
- - Have three Loop Back Mode: E1 interface Loop Back (ANA)、Ethernet interface Loop Back(DIG)、Command the remote Ethernet interface Loop Back(REM)
- - Have pseudo random code test function, easy the installation and maintenance;
- - Provide 2 impedances: 75 Ohm unbalance and 120 Ohm balance; Have Ethernet monitor self-reset function, the equipment will not dead
- - Ethernet interface supports the counters of receiving and transmitting frame, receives wrong frame counters. E1 interface supports the counters of receiving wrong frame;
- - Support SNMP Network Management;
- - Realize monitor of remote equipment temperature and voltage from local equipment;
E1 Interface | |
Interface Standard | comply with protocol G.703 |
Interface Rate | n*64Kbps±50ppm |
Interface Code | HDB3 |
E1 Impedance | 75Ω (unbalance), 120Ω (balance) |
Jitter tolerance | In accord with protocol G.742 and G.823 |
Allowed Attenuation | 0~6dBm |
Ethernet interface (10/100M) | |
Interface rate | 10/100 Mbps, half/full duplex auto-negotiation |
Interface Standard | Compatible with IEEE 802.3, IEEE 802.1Q (VLAN) |
MAC Address Capability | 4096 |
Connector | RJ45, support Auto-MDIX |
Power | |
Power supply | AC180V ~ 260V; DC –48V; DC +24V |
Power consumption | ≤10W |
Dimension | |
Product Size | 483X138X44mm(WxDxH) |
Weight | 2kg |
Working environment | |
Working temperature | -10°C ~ 50°C |
Working Humidity | 5%~95 % (no condensation) |
Storage temperature | -40°C ~ 80°C |
Storage Humidity | 5%~95 % (no condensation) |
Warranty Service:
F2H Store warrants to the purchaser that our products shall be free from defects in material and workmanship under normal use (consumables, normal tear and wear excluded) for a period of one year from the date of shipment. Any part which is determined by F2H Store to be defective in material or workmanship shall be returned to F2H Store or authorized service location, as F2H Store designates and shipping costs prepaid. Defective items will be repaired or replaced at F2H Store's option.
![]() |
ISO9001:2008 The certificate shows that a component/subsystem can be used in a specific application according to a requirement class (RC) or a integrity level (SIL). The system integrator and end user must always be aware of how to use certified components/subsystems in safety-related function, respectively a safety instrumented system. Because of the many different possibilities and how to configure a safety system, the end user must get the related information from the manufacturer of the certified component/subsystem. |
![]() |
CE The CE marking is a mandatory European marking for certain product groups to indicate conformity with the essential health and safety requirements set out in European. To permit the use of a CE mark on a product, proof that the item meets the relevant requirements must be documented. |
|
![]() |
RoHS Working in partnership with the policy lead at BERR (The Department for Business, Enterprise & Regulatory Reform), NWML is the UK Enforcement Authority for the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2008 (the “RoHS Regulations”). Manufacturers need to understand the requirements of the RoHS Directive to ensure that their products, and their components, comply. |
![]() |
FCC The Federal Communications Commission (FCC) is an independent United States government agency. The FCC was established by the Communications Act of 1934 and is charged with regulating interstate and international communications by radio, television, wire, satellite and cable. The FCC's jurisdiction covers the 50 states, the District of Columbia, and U.S. possessions. |
Write Your Own Review
Use spaces to separate tags. Use single quotes (') for phrases.
You may also be interested in the following product(s)
-
Simplex ST Adapter Plate
$10.00 -
Max 30dB, LC to LC, variable value bulkhead mechanical attenuator
$21.00 -
Max 30dB, SC to SC, variable value bulkhead mechanical attenuator
$21.00 -
Fixed value bulkhead mechanical attenuator ST - ST
$1.50 -
F2H-17M Mini Fusion splicing Machine
$1,650.00 -
F2H-UE1FE Unframed E1-FE Proposal Converter
$120.00 -
F2H-E1FE Framed E1-FE Proposal Converter
$120.00
Recent Posts
- Verizon together with Samsung announces release of 5G smartphone in first half of next year
- FirstFiber Launched their aluminium alloy Fiber Optic Splicing Closure
- FirstFiber Technologies launches 100G QSFP28 4WDM & 25G SFP28 CWDM High Frequency segment front transmission solution
- UK plans to achieve fibre-optic to every household by 2033
- 2018 China Telecom proposes future optical network development strategy
- China's broadband development white paper was first released, looking forward to quality broadband to improve quality
Check items to add to the cart or select all